@article { author = {rajae moghaddam, nahid and Tavakoli, Hossin and bagery purr, Mohamad Hossine and Bahrami, Mohamad}, title = {Reliability analysis coefficient of subgrade reaction from triaxial tests results (Case study: Kerman city)}, journal = {Journal of Analytical and Numerical Methods in Mining Engineering}, volume = {9}, number = {18}, pages = {17-29}, year = {2019}, publisher = {Yazd University}, issn = {2251-6565}, eissn = {2676-6795}, doi = {}, abstract = {Summary Induced stresses and various instabilities and deformations are resulted due to stress concentrations around a longwall face. A considerable part of the induced stresses is transferred ahead of the face and onto the adjacent T–junctions and gate roadways, which creates a zone of high stress that advances with the face advancement. A nondestructive examination based on the Seismic Moment Tensor (SMT) inversion is presented to estimate the direction of principal induced stresses around active longwall panels. The E2 longwall panel at Tabas coal mine was selected as a case study.   Introduction The induced stresses in front of the coalface can cause fractures to initiate and propagate, which in turn, lead to roof collapse. This phenomenon causes considerable problems in the face area and adjacent workings. The SMT solutions were presented for 24 seismic events at Tabas mine, which resulted in roof collapses and long delays in production. Most of the events occurred in the vicinity of the longwall face. The seismic waves generated during face advancement are used to estimate the SMTs through the process of SMT inversion.   Methodology and Approaches SMT inversion is the best method to calculate SMT from the recorded seismic parameters. The trick in the SMT inversion is to use long–period (low frequencies) regional distance seismic waves. The source process can be reduced to a simple delta function in space and time. The wave propagation is also simplified because filtering regional seismograms to long–periods, results in waves that have only propagated in a few wavelength cycles that can be easily predicted using relatively simple 1D layered earth models. The mathematical code is developed in MATLAB software to estimate the best solution for SMT. The resulted SMTs are decomposed in terms of its principal axes based on the eigenvalues and the directions of the eigenvectors. The directions of the principal induced stresses are then obtained based on the eigenvalues and the corresponding eigenvectors.   Results and Conclusions According to the results, it can be conceivable that roof falls similar to collapse of the immediate roof strata within the face area may be produced by compressive/tensile failure mechanisms, which is resulted from stress concentration and gravitational forces. These are in accordance with the directions of the principal induced stresses, which were obtained based on the eigenvalues and the corresponding eigenvectors. On the other hand, the shear failures are mainly resulted around the preexisting planes of weakness such as faults that intersected the coalface or excavation boundaries. In general, the maximum principal induced stress in all 24 events is mostly oriented with an acute angle with respect to horizon. This shows that the significant effect of horizontal induced stresses in occurrence of roof failures and face instabilities.}, keywords = {Coefficient of subgrade reaction,Triaxial test,Plat load test,Reliability,Statistical method,Probability of failure}, title_fa = {تعیین قابلیت اطمینان ضریب عکس‌العمل بستر از آزمایش‌های سه محوری خاک (مورد مطالعاتی: شهر کرمان)}, abstract_fa = {ضریب عکس‌العمل بستر به طور گسترده‌ای در محاسبات پی سازه‌های مهندسی مورد استفاده قرار می‌گیرد. تعیین ضریب عکس‌العمل بستر یکی از مباحث مهم در بخش اندرکنش خاک- سازه است. عموماً مقادیری که برای این ضریب در طراحی پی و بحث بررسی احتمال خرابی سازه به کار برده می‌شود، به صورت قطعی و بدون در نظر گرفتن تحلیل قابلیت اطمینان هستند. در این مطالعه برای تعیین قابلیت اطمینان ضریب عکس‌العمل بستر از نتایج آزمایش‌های سه محوری که نتایج آنها در فرآیندهای طراحی پی سازه‌ها به کار می‌روند، استفاده شده است. برای تعیین احتمال شکست، ابتدا این ضریب از نتایج آزمایش‌های سه محوری انجام شده در آزمایشگاه استخراج شد. سپس نتایج حاصله با مقادیر ضریب عکس‌العمل بستر به دست‌آمده از آزمایش‌های بارگذاری صفحه‌ای انجام‌شده در محل مقایسه گردیدند. در تحلیل قابلیت اطمینان (برآورد احتمال شکست)، میزان تغییرات تابع هدف با تعیین نوع تابع توزیع و بهره‌گیری از تابع بقا مشخص شد. برای نیل به این هدف، تابع توزیع نتایج ضریب عکس‌العمل بستر حاصل از آزمایش سه محوری در چهار تنش جانبی مختلف (5/0، 7/0، 3 و 2/4 کیلوگرم بر سانتی‌متر مربع) و آزمایش بارگذاری صفحه‌ای ترسیم شدند. سپس با استفاده از تابع توزیع تجمعی و تابع بقا میزان احتمال شکست محاسبه گردیدند. مقایسه نتایج به دست‌آمده نشان داد که ضریب عکس‌العمل بستر از آزمایش سه محوری با احتمال شکست بیشتری نسبت به ضریب عکس‌العمل بستر از آزمایش بارگذاری صفحه‌ای می‌تواند در محاسبات طراحی سازه وارد شود.}, keywords_fa = {ضریب عکس‌العمل بستر,آزمایش سه محوری,آزمایش بارگذاری صفحه‌ای,قابلیت اعتماد,احتمال شکست}, url = {https://anm.yazd.ac.ir/article_1364.html}, eprint = {https://anm.yazd.ac.ir/article_1364_cc04a287985df50f80075e87d8aad960.pdf} }