دانشگاه یزدروش های تحلیلی و عددی در مهندسی معدن2251-65653620140121Comparison Study between Numerical and Physical Modelling of UCS of Jointed Rock Massمقایسه مقاومت تک محوره مدل عددی و آزمایشگاهی تودهسنگ درزهدار110440FAمصطفیاسدی زادهدانشگاه تهرانرضارحمان نژادJournal Article20120409An accurate assessment of strength of jointed rock masses is one of the most important requirements in the site selection, design and successful execution of mining engineering and geotechnical projects. The strength of intact rock can be determined through standardized laboratory tests, although this is very difficult for heavily jointed rock masses. A quick estimation of these properties for preliminary evaluation of alternate sites will considerably reduce field tests costs. A large number of laboratory tests on a jointed rock mass with various joint configurations had been done by many researchers in order to determine the strength of jointed rock under uniaxial loading. In this present paper, an attempt has been made to compare the results between numerical simulation of experimental modeling on strength and deformability of jointed block masses. For this purpose, numerical simulation of experimental tests for rock mass modulus and strength has been done by 3 Dimensional Distinct Element Code (3DEC). Results showed that numerical simulation and experimental testes have a good agreement and numerical simulation can be used in order to estimate deformation modulus of rock mass.ارزیابی مقاومت توده سنگ در انتخاب محل مناسب، طراحی و اجرای موفق پروژههای معدنی و عمرانی از ملزومات اولیه است. مقاومت فشاری سنگ بکر میتواند به کمک آزمونهای استاندارد آزمایشگاهی تعیین شود، درحالیکه تعیین این پارامتر برای توده سنگ بهشدت درزهدار خیلی مشکل است. تخمین سریع این خصوصیت جهت ارزیابی اولیه، بهطور قابلملاحظهای هزینه آزمایشهای صحرایی را کاهش می دهد. آزمونهای آزمایشگاهی زیادی به وسیله محققین مختلف بر روی توده سنگ درزهدار با ترکیب درزههای متفاوت برای تعیین مقاومت فشاری تک محوری انجام شده است. در این تحقیق، مدلهای آزمایشگاهی، به کمک روش المان مجزا در حالت سه بعدی به کمک نرمافزار 3DECمدلسازی گردیده و تغییرات مقاومت حداکثر نسبت به تغییرات شیب درزه ها و گام یا قفلشدگی موردبررسی قرار گرفته است و نتایج حاصل از مدلسازی سهبعدی با نتایج آزمایشگاهی و نتایج حاصل از مدلسازی دو بعدی (نرمافزار UDEC) مورد مقایسه قرار گرفت است و ملاحظه شد که نتایج مدلسازی سه بعدی اختلاف کمتری نسبت به مدلسازی دو بعدی از نتایج آزمایشگاهی را نشان میدهند.دانشگاه یزدروش های تحلیلی و عددی در مهندسی معدن2251-65653620140121Plotting Grade-Tonnage Curves with Fractal Methods and Comparing Them by Geostatistical Methods; a Case Study: Koh-e-Zar Gold Deposit in Torbat-e-Heydaryehترسیم منحنیهای عیارـ تناژ به روشهای فرکتالی و مقایسه آن با روشهای زمین آمار (مطالعه موردی: کانسار طلای کوه زر تربت حیدریه)1122441FAحمیدگرانیانبهزادتخمه چیعباسعلیحیدریJournal Article20121111The variation in tonnage and average grade vs. cut-off grade, called grade-tonnage curves, is one of the most important factors in investment, risk assessment and uncertainty for exploitation of a deposit. These curves are plotted with the use of exploration data and through classic and geo-statistical methods. In this paper, new fractal methods have been used to plot these curves. In fractal methods, without replacing or omitting outliers, one can fit a power-law function to data. Then, using this relation, one could calculate volume (using thickness variable), average grade (using grade variable) and metal content (using grade-thickness variable) and then with these parameters, grade-tonnage curves are plotted. In this case study one of the mineralization zones of Koh-e-Zar gold deposit is used and through using number-size and concentration-area fractal models tonnage-grade curves have been plotted. Finally, the results are compared with traditional geo-statistical methods that indicate the minimum difference between geo-statistics and fractal methods in resource estimation is zero and the maximum difference is 22.2%. These differences for average grade estimation are 0.3% 14.4% respectively. The descriptive statistics proves no significant difference between the results. The most important advantages of applying fractal method include the use of initial data, the possibility of estimation with irregular and low-density data, and easier calculations.تغییرات ذخیره و عیار متوسط بر حسب تغییرات عیار حد که تحت عنوان منحنیهای عیار- تناژ از آن نام میبرند، یکی از مهمترین فاکتورهای سرمایهگذاری و تحلیل ریسک و عدم قطعیت برای بهرهبرداری از یک کانسار محسوب میشود. بهطور متداول، برای ترسیم این منحنیها از اطلاعات اکتشافی استفاده کرده و به کمک روشهای کلاسیک و زمین آمار این کار صورت میگیرد. در این مقاله روشهای جدید فرکتالی برای ترسیم این منحنیها بکار برده شده است. در روشهای فرکتالی بدون جایگزینی و یا حذف دادههای خارج از ردیف، میتوان یک رابطهی توانی بین دادهها برقرار کرد. سپس به کمک این رابطه میتوان حجم (در صورت استفاده از متغیر ضخامت)، عیار متوسط (در صورت استفاده از متغیر عیار) و مقدار فلز (در صورت استفاده از متغیر عیار× ضخامت) کانسار را محاسبه کرد و به کمک آنها منحنیهای عیار-تناژ را ترسیم نمود. یکی از زونهای کانی زایی کانسار طلای کوه زر تربتحیدریه به عنوان مطالعه موردی استفاده شده است و به کمک روشهای فرکتالی عددی- اندازهای و عیار- مساحت منحنیهای عیار- تناژ آن محاسبه و ترسیم شده است. سپس نتایج بهدستآمده با روشهای مرسوم زمین آمار مقایسه شده است. محاسبات نشان میدهد که حداقل اختلاف بین روشهای زمین آمار و فرکتالی در برآورد ذخیره صفر و حداکثر 2/22% و برای عیار متوسط حداقل 3/0% و حداکثر 4/14% است. عدم وجود اختلاف معنیدار بین نتایج توسط آمار توصیفی ثابت شده است. مهمترین مزیت استفاده از روشهای فرکتالی استفاده از دادههای خام، امکان برآورد با دادههای نامنظم و چگالی کم و محاسبات سادهتر است.دانشگاه یزدروش های تحلیلی و عددی در مهندسی معدن2251-65653620140121Effect of Time Step in Accuracy of Particle Movement Prediction using Discrete Element Method (DEM)تأثیر گام زمانی بر دقت نتایج در شبیهسازی حرکت ذرات به روش اجزای گسسته (راگ)2332442FAعلیرضاقاسمیسیدامیدموسویصمدبنیسیJournal Article20130410Discrete Element Method (DEM) is extensively used to simulate the behavior of particles in various processing units. This method is based on modeling the forces acting between particles in any contact and consequently calculating the new position of particles. The high number of elements and numerous equations is very time-consuming even when using computers with very fast processors. The required computation time mainly depends on the time step. If the time step is chosen very short, the computation time will significantly increase. On the other hand, if the time step is chosen very long, the simulation will be Inaccurate due to not fully observing the contacts. In DEM calculations, the time step is chosen as a fraction of the collision time. In this research, a relationship was proposed between the contact time fraction and the error of simulation. In other words, to select the time step in addition to physical parameters, the accuracy of the simulation was also accommodated in the frequently-used relationships. The required time steps to achieve the simulation error of 5% were calculated for two common contact-force models namely, Hertz-Mindlin and linear spring-dashpot. The simulation was performed for two particles with radius of 3 cm, Elasticity modulus of 210 GPa, Poisson's ratio of 0.3 and relative velocity of 0.5 m/s. The required time steps were found to be 2.3 and 0.19 µs for the Hertz-Mindlin and linear spring-dashpot contact-force models, respectively. Results showed that with a scale-downing the modulus from 210 GPa to 2.1 MPa, the required time steps for the Hertz-Mindlin and linear spring-dashpot contact force models, with equal simulation error, increased by 100 and 316 times, respectively.روش اجزای گسسته (راگ) جهت شبیهسازی حرکت ذرات در سیستمهای فرآوری کاربرد وسیعی دارد. اساس این روش محاسبه نیروهای متقابل میان ذرات در هر برخورد و مدل کردن موقعیت جدید ذرات است. تعداد زیاد اجزا و روابط متعدد، باعث طولانی شدن زمان انجام محاسبات در راگ میشود. زمان لازم برای محاسبات بستگی زیادی به گام زمانی انتخابشده برای شبیهسازی دارد. اگر گام زمانی کوچک در نظر گرفته شود، حجم محاسبات و به دنبال آن زمان لازم جهت شبیهسازی افزایش مییابد. از طرف دیگر، در صورتی که گام زمانی بزرگ در نظر گرفته شود، شبیهسازی به دلیل عدم توجه لازم به فرآیند برخورد، با خطا همراه خواهد بود. در راگ گام زمانی به صورت ضریبی از زمان تماس دو ذره در یک برخورد، در نظر گرفته میشود. هدف این پژوهش ارائهی رابطهای برای تعیین گام زمانی شبیهسازی با توجه به شرایط عملیاتی و میزان خطای شبیهسازی بود. برای این کار ابتدا رابطهی بین ضریب زمان تماس و خطای شبیهسازی ارائه شد و روابط معمول زمان تماس اصلاح گردید. نتایج نشان دادند که گام زمانی لازم جهت شبیهسازی با خطای 5% برای ذراتی به شعاع 3 سانتیمتر، مدول الاستیسیتهی 210 گیگا پاسکال با سرعت نسبی برخورد 5/0 متر بر ثانیه، با استفاده از مدل نیروی برخورد هرتز- میندلین 3/2 میکروثانیه است که تقریباً 12 برابر بیشتر از مدل خطی است. به منظور سرعت بخشیدن به محاسبات که با بزرگ مقیاس کردن اندازهی ذرات حاصل میشود، مشخص گردید که با افزایش شعاع ذرات به 1 متر، گام زمانی لازم برای شبیهسازی، 33 برابر افزایش مییابد. کاهش مدول الاستیسیته به مقدار 1/2 مگاپاسکال باعث افزایش 316 برابری گام زمانی در مدل خطی و 100 برابری در مدل هرتز- میندلین گردید.دانشگاه یزدروش های تحلیلی و عددی در مهندسی معدن2251-65653620140121Application of Principal Component Analysis in Prediction of Penetration Rate of TBM Using Artificial Neural Networksکاربرد روش آنالیز مؤلفههای اصلی در پیشبینی نرخ نفوذTBM با استفاده از شبکههای عصبی مصنوعی3343443FAمحمدمختاریاندانشگاه صنعتی اصفهانمصلحافتخاریدانشگاه صنعتی اصفهانعلیرضاباغباناندانشگاه صنعتی اصفهانJournal Article20130511Performance analysis and accurate prediction of Penetration Rate (PR) of a TBM have been the ultimate goals of many research works. A reliable prediction of a TBM performance is necessary in budget control and also time schedule planning in underground excavation projects. This research aims to investigate the application of Principal Component Analysis (PCA) in prediction of penetration rate of TBM using Artificial Neural Networks (ANN), which has not been used and reported in previous studies in this field of study. PCA is a statistical procedure that uses an orthogonal transformation to convert a set of observations of possibly correlated variables into a set of values of linearly uncorrelated variables called principal components. In this study, the obtained data from 10 KM of excavated Zagros tunnel project in Iran are used to predict PR of a TBM using ANN modeling. For predicting PR of TBM, mechanical properties of intact rock and rock masses and also operational parameters such as recorded values of torque and thrust are required. Various simulations with and without PCA have been conducted to achieve the optimum network for predicting PR. The obtained results of simulation show that the network with PCA is more appropriate and the network with 11 principal components as input parameters and 16 neurons in hidden layer is the optimum structure for predicting of PR in this study. The results of developed ANN method show that the optimum network is very efficient for predicting the PR in Zagros tunnel.از فاکتورهای مهم در پیشبینی عملکرد TBM، تعیین نرخ نفوذ حفاری و نرخ پیشروی است. هدف اصلی از این مطالعه، بررسی استفاده از آنالیز مؤلفههای اصلی در پیشبینی نرخ نفوذ TBMبا استفاده از روش شبکههای عصبی مصنوعی است. یکی از بخشهای مهم در استفاده از روش شبکههای عصبی به منظور پیشبینی، انتخاب پارامترهای ورودی است. آنالیز مؤلفههای اصلی یکی از روشهایی است که با استفاده از آن میتوان پارامترهای مؤثر بر نرخ نفوذ را مشخص کرد. برای دستیابی به این هدف، یک پایگاه داده متشکل از خواص توده سنگ، خواص ماده سنگ و مشخصات ماشین ایجاد شده است و سپس نرخ نفوذ با منظور کردن چندین مدل ورودی با استفاده از شبکههای عصبی مصنوعی در 10 کیلومتر حفاری تونل زاگرس بدون آنالیز مؤلفههای اصلی پیشبینی شده است و سپس با توجه به تعدد پارامترهای ورودی در شبکه از آنالیز مؤلفههای اصلی در انتخاب بهترین پارامترهای ورودی استفاده شده است که در نهایت شبکهای با 11 ورودی، مورد تأیید قرار گرفته است. از مقایسه نتایج پیشبینی نرخ نفوذ با استفاده از شبکههای عصبی مصنوعی بدون آنالیز مؤلفههای اصلی و شبکه عصبی مصنوعی با آنالیز مؤلفههای اصلی این نتیجه حاصل میشود که استفاده از آنالیز مؤلفههای اصلی تأثیر به سزایی در انتخاب پارامترهای ورودی شبکه و همچنین نتایج پیشبینی دارد.دانشگاه یزدروش های تحلیلی و عددی در مهندسی معدن2251-65653620140121An Approach for Risk Assessment in Open Pit Mines Using FAHP & Fuzzy TOPSIS Methodsارائه رویکردی جهت ارزیابی ریسک در معادن روباز با استفاده از روش FAHP و Fuzzy TOPSIS4558444FAاحمدرضاصیادیدانشگاه تربیت مدرسمسعودمنجزیدانشگاه تربیت مدرس0000-0001-6376-9181محمدرضاشریفیدانشگاه تربیت مدرسJournal Article20130611Mining due to its specific characteristic is considered as a hazardous industry. Risk assessment is one of the most important project management procedures. The aim of this research is to present an approach for identification and ranking risks in the open pit mines. Ranking is a multi-attribute decision making. In order to identify the risks, risk breakdown structure method and ranking risks by Fuzzy TOPSIS method is implemented. First a comprehensive structure of risks in open pit mines in the frame work of 20 main levels and 117 sublevels is designed. Then different indices such as “probability”, “impact on project objectives (time, cost, quality and performance)’’, “manageability”, “continually repeating”, “exposure”, “proximity”, “ confidence level” for ranking of risk issues are determined. This approach is applied for risk assessment of Zarshuran Gold Mine as one of the biggest goldmines in Iran. In this mine, marketing, geotechnical, economic and political risks have been identified as the most significant risks, respectively.معدنکاری به دلیل ویژگیهای خاص خود از جمله صنایع پرمخاطره بوده و ارزیابی ریسک یکی از مهمترین مراحل مدیریت پروژه محسوب میشود. هدف از این تحقیق ارائه رویکردی جهت شناسایی و رتبهبندی ریسکها در معادن روباز است. رتبهبندی یک مسئله تصمیمگیری چند شاخصه است. به منظور شناسایی ریسکها از روش ساختار شکست ریسک و جهت رتبهبندی از روش Fuzzy TOPSISاستفاده شده است. در این راستا ابتدا ساختار جامعی از ریسکها در معادن روباز در قالب 20 سطح اصلی و 117 زیر سطح تهیه شده است. سپس شاخصهای متعددی شامل احتمال وقوع، اثر بر اهداف پروژه (زمان، هزینه، کیفیت و محدوده)، مدیریتپذیری، تناوب تکرار، میزان کشف، نزدیکی وقوع و سطح اطمینان ریسک جهت رتبهبندی عوامل ریسک تعیین گردید. از این رویکرد جهت ارزیابی ریسک معدن طلای زرشوران به عنوان بزرگترین معدن طلای کشور استفاده گردید. در این معدن ریسکهای بازار، ژئوتکنیکی، اقتصادی و سیاسی به ترتیب به عنوان مهمترین ریسکها شناسایی شدهاند.دانشگاه یزدروش های تحلیلی و عددی در مهندسی معدن2251-65653620140121A Preliminary Design of cavern for Underground Compressed Gas Storage in Ardebil City using Flac3D Softwareپایداری مغار سنگی با نرمافزار FLAC3D، برای طراحی اولیه مخزن زیرزمینی ذخیرهسازی گاز فشرده شهر اردبیل5967445FAحسینایمانیدانشگاه بینالمللی امام خمینی (ه) قزوینمهدیحسینیدانشگاه بینالمللی امامخمینی (ه) قزوینحسینجلالی فردانشگاه شهید باهنر کرمانJournal Article20130812Today, natural gas storage in underground is received much attention. It is a fundamental technique to control consumption particularly during the cold months of the year. For this purpose, several methods are used for underground storage of gas, such as reservoirs, aquifers, salt caverns, rock caverns (lined or unlined) and abandoned mines. Each of these methods is selected according to the geo-mechanical and hydro-mechanical characteristics of the region such as permeability, porosity, aquifer level, compressive strength and tensile strength of rocks, and internal pressure of stored gas. In this research, based on the geological, hydrogeological and geo-mechanical conditions prevailing in Ardebil area, the best method was selected. Primary studies have indicated that storage in both lined and unlined rock caverns is possible. The cavern has 235 and 81m burden for unlined and lined design respectively. However, lined rock cavern has priority in this area. A numerical approach was used for analyzing the stability of storage cavern. There are not many discontinuities in the area therefore FLAC<sup>3D</sup> was selected for numerical analysis. The results of the analyses showed that the induced strains around the lined cavern before and after gas injection appeared to be less than the critical strains calculated by Sakurai’s relation. Therefore, the storage cavern should be stable and gas storage at this cavern is possible with 2 MPa internal Pressure.امروزه ذخیرهسازی گاز طبیعی در فضاهای زیرزمینی به عنوان یک راهکار اساسی جهت کنترل بازار مصرف به ویژه در ماههای سرد سال مورد توجه بسیار قرار گرفته است. بدین منظور روشهای متعددی جهت ذخیرهسازی زیرزمینی گاز استفاده میشود که عبارتاند از: ذخیرهسازی در میدانهای تخلیهشده نفت و گاز، آبخوانها (سفرههای آب زیرزمینی)، حفریات نمکی، حفریات سنگی (حفریات سنگی آستردار یا بدون آستر) و معادن متروکه که انتخاب هر کدام از این روشها با توجه به ویژگیهای ژئومکانیکی و هیدرومکانیکی منطقه از قبیل نفوذپذیری، تخلخل، تراز سفره آب زیرزمینی، مقاومت فشاری و کششی سنگ و نیز فشار داخلی گاز ذخیرهشده صورت میگیرد. در این تحقیق ضمن بررسی شرایط زمینشناسی مهندسی، هیدروژئولوژی و ژئومکانیکی سنگهای محدوده موردنظر (منطقه اردبیل) بهترین روش ذخیرهسازی گاز فشردهشده تعیین شد. ارزیابیها و بررسیهای اولیه نشان میدهد که ذخیرهسازی، در هر دو حالت حفریات سنگی بدون آستر و با آستر، امکانپذیر است. با به دست آوردن خواص فیزیکی و مکانیکی سنگ منطقه موردمطالعه، عمق قرارگیری مغار بدون آستر حداقل 235 متر و مغار با آستر 81 متر، تخمین زده شد. در این میان ایجاد حفریات سنگی با آستر از اولویت بیشتری برخوردار است. برای تحلیل پایداری مخزن ذخیرهسازی از روش عددی استفاده گردید و با توجه به عدم وجود ناپیوستگی، نرمافزار FLAC<sup>3D</sup> انتخاب شد. نتایج تحلیل نشان میدهد که جابجاییهای اطراف مغار با آستر قبل و بعد از تزریق گاز کمتر از جابجاییهای بحرانی بهدستآمده از روابط ساکورایی است. در نتیجه مغار ذخیرهسازی پایدار خواهد بود و امکان ذخیرهسازی گاز در این مغار با فشار داخلی 2 مگاپاسکال میسر است.دانشگاه یزدروش های تحلیلی و عددی در مهندسی معدن2251-65653620140121Recognition of Cu-Porphyry Mineralization Areas by Using One and multivariate integration methods on drainage geochemical data in Ghale Askar area, Kerman provinceشناسایی مناطق کانی زایی مس پورفیری با استفاده از تلفیق روشهای تک متغیره و چند متغیره بر روی داده های ژئوشیمیایی آبراهه ای در منطقه قلعه عسکر، استان کرمان6982446FAسمیهعباس زادهدانشگاه شهید باهنر کرمانغلامرضارحیمیپوردانشگاه شهید باهنر کرمانمجیدنجم الدینیدانشگاه آزاد اسلامیJournal Article20131112Ghale–Askar area is located in the east north of Baft city in which Cu-porphyry mineralization has occurred. 63 samples were analyzed for 24 elements such as U , Th, Ba, W,As, Mo, S, Bi, Re, Sn, Cr, Ni, V, Co, Sr, Zn, Mn, Cd, Pb, Sb, Au, Cu, Ag and Hg with ICP-Ms method. One and multivariate statistical techniques were applied on drainage geochemical data. To draw the map of elements’ anomaly, the threshold was calculated with gap statistics and methods; the results of the mentioned methods specified that the threshold value obtained from approach was greater than that of gap statistics and its map represented smaller region. The results of hierarchical cluster method showed six separated clusters that the fourth cluster including (Bi, Cu, S) and the fifth cluster including (Ni, U, Mo, S, Th, Cr) were identified as the center of mineralization. Moreover, the results of K-mean cluster method confirmed the results of hierarchical cluster method and represented the center of mineralization in red and green colors in that region. Besides, factor analysis was carried out and studying eigenvalues of the sixth factor described that it was the center of mineralization. Finally, the results were integrated and identified the best regions for the future studies. <em>منطقه</em> قلعه عسگر در استان کرمان در شمال شرقی شهرستان بافت واقع شده است. در منطقه فوق کانیزایی مس پورفیری رخ داده است. برای تعیین مناطق مرکزی و حاشیهای کانیزایی 63 نمونه آبراههای از منطقه قلعه عسکر جمعآوری و به روش ICP-MS برای عناصر U, Th, Ba, W,As, Mo, S, Bi, Re, Sn, Cr, Ni, V, Co, Sr, Zn, Mn, Cd, Pb, Sb, Au, Cu, Ag وHg. تجزیه شدند.آنالیزهای تک متغیره و چند متغیره (خوشهای و فاکتوری) بر روی دادههای فوق انجام شد که برای رسم نقشه بیهنجاری هر عنصر ابتدا حد آستانهای آن با دو روشتک متغیره(آمار انفصال و )محاسبه شد. نتایج این دو روش نشان داد که مقدار حد آستانه با روش نسبت به روش آمار انفصال بیشتر است و نقشه بیهنجاری هر عنصر محدوده کوچکتری را نشان میدهد. نتایج آنالیز خوشهای سلسله مراتبی شش خوشه جداگانه نشان داد که خوشه چهارم شامل عناصر Bi, Cu, Sr و خوشه پنجم شامل عناصر Cr, Ni, U, Mo, S, Th به عنوان مرکز کانیزایی مشخص شدند همچنین نتایج آنالیزK-means Cluster نتایج آنالیز خوشهای سلسله مراتبی را تأیید کردند و دو خوشه کانی زایی فوق را به رنگ قرمز و سبز در منطقهنشان دادند. بر روی دادههای فوق همچنین آنالیز فاکتوری نیز انجام شد که با مطالعه مقادیر ویژه فاکتور ششم مشخص شد که این فاکتور نشاندهنده مناطق مرکزی کانیزایی است. در نهایت نتایج فوق با هم تلفیقشده و بهترین مناطق امیدبخش برای مطالعات آتی مشخص شدند.دانشگاه یزدروش های تحلیلی و عددی در مهندسی معدن2251-65653620140121Determination of Elemental Paragensis at Gushfil (Irankuh) Pb-Zn Deposit by Mineralographic and Geochemical Studiesمطالعات ژئوشیمیایی و کانی شناختی کانسار سرب و روی گوشفیل ایرانکوه، اصفهان8391447FAفریماهآیتیدانشگاه پیام نورهنگامهدهقانیدانشگاه صنعتی اصفهاناحمدرضامختاریدانشگاه صنعتی اصفهانسید حسینمجتهد زادهدانشگاه یزدJournal Article20140312Pb-Zn deposits at Irankuh range are located along Irankuh Mountain 25 km south west of Isfahan along Sanandaj-Sirjan structural zone. The host rocks of the deposit are mainly Cretaceous carbonate and Jurassic shale units; however, it is mainly formed inside carbonate unit. Sulphide minerals of the deposit are mainly composed of sphalerite, galena and pyrite. The most abundant mineral is sphalerite that is evenly distributed in a matrix rich of pyrite and galena. Pyrite is one of the commonly found minerals which are formed during most of mineralisation episodes as intergrowth. This research focuses on recognition of pathfinder and paragenetic elements in Gushfil deposit and origin mineral of these elements. Based on the performed analyses (ICP-OES) on shale, dolomite an ore samples (collected in the area) and their comparison with local and global shale analyses the following elements are determined Ag, Sb, Cd, Co, Li, Zn and Pb and the bearing minerals are sphalerite, galena and pyrite.ﮐﺎﻧﺴﺎر ﺳﺮب و روی اﻳﺮاﻧﻜﻮه در فاصله 25 کیلومتری جنوب غرب اصفهان و در زون ساختاری سنندج - سیرجان واقع شده است. سنگهای در ﺑﺮﮔﻴﺮﻧﺪه ﻛﺎﻧﺴﺎر عمدتاً سنگهای ﻛﺮﺑﻨﺎﺗﻲ ﻛﺮﺗﺎﺳﻪ و ﺷﻴﻞ ژوراﺳﻴﻚ اﺳﺖ. ﻛﺎﻧﻪ زاﻳﻲ که عمدتاً در نهشتههای ﻛﺮﺑﻨﺎﺗﻪ ﺻﻮرت ﭘﺬﻳﺮﻓﺘﻪ شامل اسفالریت، گالن و پیریت است. اسفالریت فراوانترین کانی سولفیدی است که بهطور یکنواخت در ماتریکس غنی از پیریت و گالن پراکنده است. پیریت در اغلب مراحل کانه زایی به صورت همرشدی با اسفالریت وجود دارد. کالکوپیریت به صورت اکسولوشن در جهت کلیواژهای اسفالریت قابل مشاهده است. ظاهراً گالن زودتر از اسفالریت ته نشین شده که این امر میتواند به دلیل تحرک کمتر عنصر سرب در مقایسه با روی در محلولهای گرمابی باشد. این پژوهش بر تشخیص عناصر ردیاب و پاراژنزهای عنصری در کانسار گوشفیل و شناسایی کانیهای منشأ این عناصر تمرکز یافته است. بر اساس مقایسه نتایج آنالیزهای ICPانجامشدهدر سنگ شیل و دولومیت نهشته معدنی گوشفیل و عناصر موجود در شیل و دولومیت جهانی و شیل و دولومیت زمینه، بهترین عناصر ردیاب را میتوان Ag, Sb,Cd, Cr, Zn, Pbمعرفی نمود. با توجه به آنالیز الکترومایکروپروب منشأ عناصر ردیاب مشخصشده، کانیهای اسفالریت، گالن و پیریت است.دانشگاه یزدروش های تحلیلی و عددی در مهندسی معدن2251-65653620140121Estimating Joint Normal and Shear Stiffness Coefficient Using Statistical Methodsتخمین ضرائب سختی قائم و برشی ناپیوستگی ها بهروش آماری93103448FAنورالدیننیک عادتدانشکده مهندسی معدن و متالورژی، دانشگاه یزدعلیرضایاراحمدی بافقیدانشکده مهندسی معدن و متالورژی، دانشگاه یزد0000-0002-4594-0288Journal Article20140511In analyzing stability of geo-mechanical structures, considering the strength parameters of intact rock and discontinuity is of paramount importance. In jointed rocks, instable conditions are controlled in multiple manners by coefficient of discontinuity strength. The compressive strength of joint surface, roughness coefficient, deformation modules of rock mass and normal and shear stiffness coefficient are among the most important influential parameters in the behavior of discontinuities that often is estimated by experimental and in-situ tests. Among these parameters, estimating joint normal and shear stiffness coefficient, is expensive because it needs in-situ tests and use of huge and costly equipment, and there is a high probability of experimental and human error in it. In this study it has been tried to calculate some of the parameters of intact rocks and discontinuities that seem relevant to discontinuity normal and shear stiffness coefficient by using quantitative values. Therefore, the present data were gathered from the results of various experimental and in-situ tests and then were studied. Statistical analysis of single and multivariable of this data indicated that there is a considerable relationship between normal and shear stiffness coefficient with intact rock and discontinuity parameters in a way that estimating normal and shear stiffness coefficient from other parameters became possible.در تحلیل پایداری سازههای ژئومکانیکی، توجه به پارامترهای مقاومتی سنگ بکروناپیوستگی هاازاهمیتبسزایی برخورداراست. در محیطهای ناپیوسته سنگی، شرایط ناپایداری به صورت مضاعف توسط ضرایب مقاومتی ناپیوستگیها کنترل میشود. مقاومت فشاری سطوح درزه، ضریب زبری، مدول تغییر شکلپذیری توده سنگ، ضریب سختی نرمال و برشی از مهمترین پارامتر های تأثیرگذار بر رفتار ناپیوستگیها میباشند که اغلب توسط آزمایشهای آزمایشگاهی و صحرایی تعیین میشوند. از میان این پارامترها، تعیین ضریب سختی نرمال و برشی درزه، به علت نیاز به انجام آزمایشهای برجا و استفاده از تجهیزات بزرگ و گران قیمت، هزینه بر بوده و امکان وجود خطای آزمایشگاهی و انسانی در محاسبه آنها بالا است. در این پژوهش تلاش شده است که با استفاده از مقادیر کمی برخی از پارامترهای سنگ بکر و ناپیوستگی ها که به نظر میرسند با ضریب سختی نرمال و برشی ناپیوستگی در ارتباط باشند مقادیر این ضرایب تخمین زده شود. برای این منظور، دادههای موجود حاصل از آزمایشهای مختلف آزمایشگاهی و برجا جمعآوری و مطالعه گردید. تحلیلهای آماری تک متغیره و چند متغیره این دادهها ارتباط قابلتوجهی میان ضریب سختی نرمال، برشی و پارامترهای سنگ بکر و ناپیوستگیها را نشان داد بهطوریکه تخمین ضریب سختی نرمال و برشی ناپیوستگیها از دیگر پارامترها مانند زبری درزه، مقاومت فشاری درزه، مدول تغییر شکل پذیری تودهسنگ، مدول سنگ و مقاومت فشاری تک محوره ممکن گردید.