Crack growth mechanism in granite specimens with non-persistent joints under punch shear through test

Document Type : Research Article

Authors

1 Dept. of Mining Engineering, Hamadan University of Technology, Hamadan, Iran

2 Dept. of Mining and Metallurgy, Yazd University, Yazd, Iran

3 Rahsazi & Omran Iran construction Company, Tehran, Iran

Abstract

Experimental and numerical methods (Particle Flow Code) were used to investigate the effect of echelon notches on the shear behavior of the joint’s bridge area in granite. A punch-through shear test was used to model the granite cracks under shear loading. Granite samples with dimension of 20 mm×150 mm×40 mm were prepared in the laboratory. Within the specimen model and near the edges, four edge notches were provided. Nine different configuration systems were prepared for notches. In these configurations, the length of each notch was taken as 3 cm, 4cm and 5 cm. Assuming a plane strain condition, special rectangular models were prepared with dimensions of 100 mm×100 mm using the particle flow code in two dimensions (PFC2D). Similar to those joints’ configuration systems in the experimental tests, i.e. 9 models with different rock bridge lengths and different rock bridge joint angles were prepared. The axial load was applied to the punch through the central portion of the model. This testing showed that the failure process was mostly governed by the rock bridge length and the rock bridge angle.  Shear strengths of the specimens were related to fracture pattern and failure mechanism of the discontinuities. It was shown that the shear behavior of discontinuities is related to the number of the induced tensile cracks which are increased by increasing the rock bridge angle.  The strength of samples decreases with increasing the joint length. The failure pattern and failure strength are similar in both methods, i.e. the experimental testing and the numerical simulation.

Keywords

Main Subjects


[1]          Wong, R.H.C. (1998), “Crack coalescence in a rock-like material containing two cracks”, Int. J. Rock Mech. Min. Sci., 35(2), 147-164.
[2]          Yang, S.T., (2011), “Influence of local fracture energy distribution on maximum fracture load of three point-bending notched concrete beams”, Eng. Fract. Mech., 78, 3289-99. 
[3]          Chen, X., Liao, Z.H. (2013), “Cracking process of rock mass models under uniaxial compression”, J. Central South Univ., 20(6), 1661-1678.
[4]          De Bremaecker, J.C. (2004), “Numerical models of shear fracture propagation”, Engineering Fracture Mechanics., 71(15), 21612178.
[5]          Haeri, H., Marji, MF. (2015), “Experimental and Numerical Simulation of the Microcrack Coalescence Mechanism in Rock-Like Materials” strength of materials 47 (5), 740-754.
[6]          Haeri, H. and Sarfarazi, V. (2016a), “The effect of micro pore on the characteristics of crack tip plastic zone in concrete”, Comput. Concrete, 17(1), 107-12.
[7]          Haeri, H. and Sarfarazi, V. (2016b), “The effect of non-persistent joints on sliding direction of rock slopes”, Comput. Concrete, 17(6), 723-737.
[8]          Haeri, H. and Sarfarazi, V. (2016c), “The deformable multi-laminate for predicting the elasto-plastic behavior of rocks”, Comput. Concrete, 18, 201-214.
[9]          Haeri, H., and Fatehi Marji, M. (2015), “Fracture analyses of different pre-holed concrete specimens under compression”, Acta Mech Sin, 31(6), 855-870.
[10]        Haeri, H., Sarfarazi, V. (2016d), “Experimental study of shear behavior of planar non-persistent joint”, Comput. Concrete, 17(5), 639-653.
[11]        Haeri, H., Shahriar, K., Marji, M.F. (2013), “Modeling the propagation mechanism of two random micro cracks in rock Samples under uniform tensile loading”, 13th International Conference on Fracture, Beijing, China.
[12]        Sarfarazi, V. and Haeri, H., (2016a), “Effect of number and configuration of bridges on shear properties of sliding surface”, J. Min. Sci., 52(2), 245-257.
[13]        Sarfarazi, V., (2016b), “A new approach for measurement of anisotropic tensile strength of concrete”, Adv. Concrete Constr., 3(4), 269-284.
[14]        Sarfarazi, V., (2014), “Numerical simulation of the process of fracture of Echelon rock joints”, Rock Mech. Rock Eng., 47(4), 1355-1371.
[15]        Sarfarazi, V., (2016), “The effect of non-persistent joints on sliding direction of rock slopes”, Comput. Concrete, 17(6), 723-737.
[16]        Sardemir, M. (2016), “Empirical modeling of flexural and splitting tensile strengths of concrete containing fly ash by GEP”, Comput. Concrete, 17(4), 489-498.
[17]        Wang, X., Zhu, Z.,  (2017), “Study of rock dynamic fracture toughness by using VB-SCSC specimens under medium-low speed impacts”, Eng. Fract. Mech., 181, 52-64.
[18]        Hosseini_Nasab, H., Fatehi Marji M. (2007)  A semi-infinite higher-order displacement discontinuity method and its application to the quasistatic analysis of radial cracks produced by blasting, Journal of Mechanics of Materials and Structures 2 (3), 439-458.
[19]        Marji,  MF. (2013) On the use of power series solution method in the crack analysis of brittle materials by indirect boundary element method, Engineering Fracture Mechanics 98, 365-382.
[20]        Marji, MF. (2014) Numerical analysis of quasi-static crack branching in brittle solids by a
modified displacement discontinuity method, International Journal of Solids and Structures 51 (9), 1716-1736.
[21]        Marji, MF. (2015) Simulation of crack coalescence mechanism underneath single and double disc cutters by higher order displacement discontinuity method, Journal of Central South University 22 (3), 1045-1054.
[22]        Cundall, P.A. (1979), “A discrete numerical model for granular assemblies”, Geotechnique, 29(1), 47-65.
[23]        Kulatilake, P.H.S.W., Malama, B. (2001), “Physical and particle flow modeling of jointed rock block behavior under uniaxial loading”, Int. J. Rock Mech. Min. Sci., 38(5), 641-657.
[24]        Ghazvinian, A., Sarfarazi, V., (2012), “A study of the failure mechanism of planar non-persistent open joints using PFC2D”, Rock Mech. Rock Eng., 45(5), 677-693.
[25]        Zhang, X.P (2013), “Crack initiation, propagation and coalescence in rock-like material containing two flaws: a numerical study based on bonded-particle model approach”, Rock Mech. Rock Eng., 46(5), 1001-1021.
[26]        Bahaaddini, M., Sharrock, G. (2013), “Numerical investigation of the effect of joint geometrical parameters on the mechanical properties of a non-persistent jointed rock mass under uniaxial compression”, Computer. Geotechnic., 49, 206-225.
[27]        Kallimogiannis V., Saroglou H., (2017), Study of Cracking Process in Granite, Procedia Engineering    191, 1108 – 1116.
[28]        D. O. Potyondy and P. A. Cundall, (2004) “A bonded-particle model for rock,” International Journal of Rock Mechanics and Mining Sciences, 41(8): 1329–1364.