رضائی, محسن, غفوری, محمد, اجل لوئیان, رسول. (1395). تأثیر میزان تنش و ابعاد صفحه بر مدول تغییر شکل توده سنگ در آزمایش بارگذاری صفحهای. روش های تحلیلی و عددی در مهندسی معدن, (), -.
محسن رضائی; محمد غفوری; رسول اجل لوئیان. "تأثیر میزان تنش و ابعاد صفحه بر مدول تغییر شکل توده سنگ در آزمایش بارگذاری صفحهای". روش های تحلیلی و عددی در مهندسی معدن, , , 1395, -.
رضائی, محسن, غفوری, محمد, اجل لوئیان, رسول. (1395). 'تأثیر میزان تنش و ابعاد صفحه بر مدول تغییر شکل توده سنگ در آزمایش بارگذاری صفحهای', روش های تحلیلی و عددی در مهندسی معدن, (), pp. -.
رضائی, محسن, غفوری, محمد, اجل لوئیان, رسول. تأثیر میزان تنش و ابعاد صفحه بر مدول تغییر شکل توده سنگ در آزمایش بارگذاری صفحهای. روش های تحلیلی و عددی در مهندسی معدن, 1395; (): -.
تأثیر میزان تنش و ابعاد صفحه بر مدول تغییر شکل توده سنگ در آزمایش بارگذاری صفحهای
تاریخ دریافت: 04 مهر 1394،
تاریخ بازنگری: 13 مهر 1395،
تاریخ پذیرش: 20 آذر 1395
چکیده
مدول تغییر شکل توده سنگ، از مهمترین پارامترهای توده سنگ بوده و در طراحی های مهندسی سنگ، به عنوان مهمترین پارامتر ورودی مورد استفاده قرار میگیرد. این پارامتر به دو روش مستقیم و غیر مستقیم بدست میآید. در روش غیر مستقیم، با استفاده از روابط تجربی مختلف، که طبقهبندیهای توده سنگ و یا پارامترهای ژئومکانیکی توده سنگ را با این پارامتر همبسته کرده اند، برآورد میگردد. در روش مستقیم، با استفاده از آزمایشهای برجای مختلف، این پارامتر اندازهگیری میشود. هر یک از آزمایشهای برجا با توجه به حجمی از توده سنگ، که تحت تأثیر قرار میدهند، دارای دقت خاصی در نتایج به دست آمده میباشند. آزمایش بارگذاری صفحهای با توجه به حجم نسبتاً بزرگی از سنگ، که تحت تأثیر قرار میدهد و نیز روش انجام ساده تر آن، از معمولترین آزمایشها برای اندازهگیری مدول تغییر شکل برجای توده سنگ است. در طی این آزمایش، تنش بصورت چرخههای بارگذاری و باربرداری به توده سنگ وارد میگردد و جابجایی ایجاد شده در توده سنگ اندازهگیری میشود. این آزمایشها بسته به هدف آزمایش و کاربرد نتایج آن، با تنشهای متفاوت و اندازه صفحات بارگذاری متفاوت انجام میشوند. در این پژوهش، مقایسهای بین نتایج آزمایشهای انجام شده با دو تنش مختلف و همچنین صفحات با قطر متفاوت صورت گرفته است. در این مقایسه از روش های آماری تحلیل همبستگی و آزمون t با زوج داده ها استفاده گردید. نتایج تحلیل های انجام شده بر روی آزمایشهای با حداکثر تنشهای 20 و 40 مگاپاسکال، نشان میدهد که بین نتایج آزمایش با بارهای مختلف، اختلاف معنیداری وجود ندارد و میزان حداکثر تنش وارده بر سنگ، بر مدول تغییر شکل بدست آمده از آزمایش، تأثیری نداشته است ولی نتایج حاصل از آزمایشهایی که با دو صفحه با قطرهای متفاوت در یک موقعیت انجام گردیدهاند، نشان میدهد که، اختلاف معنی داری بین آنها وجود دارد و مدول تغییر شکل بدست آمده از آزمایش با صفحات با قطر بزرگتر، در توده سنگهای با کیفیت بالا، بزرگتر از صفحات با قطر کمتر بوده و در توده سنگ های ضعیف، برعکس است. به نظر میرسد، این اختلاف ناشی از تأثیر نسبت ابعاد صفحه بارگذاری به ابعاد گالری آزمایش باشد.
Effects of Stress Value and Loading Plate Dimensions on In-situ Deformation Modulus of Rock Mass in Plate Loading Test
نویسندگان [English]
Mohsen Rezaei1؛ Mohammad Ghafoori2؛ Rasoul Ajalloeian3
چکیده [English]
Rock mass deformation modulus (Erm) has been considered as the most typical parameter illustrating the pre-failure mechanical behavior of rock mass. Erm is a basic input parameter for most rock engineering projects including tunneling, support designing, foundation designing, etc. For these purposes, it is necessary to obtain this parameter before starting numerical modeling. Intact rock elastic modulus is measured by uniaxial compression strength test in laboratories. But, the existence of discontinuities, makes a great difference between the mechanical properties of rock mass and intact rock. Erm can be estimited by emprical equations or determined by in-situ tests such as plate loading, dilatometer, flat jacking, and radial jacking tests. The plate loading test is a common test to determaining rock mass deformation modulus of rock mass that has been used in several project around the world. Erm of rock masses in Bakhtiari dam site is determined by Plate loading tests using different loading plate sizes and different stress values. Bakhtiari dam site is located in southwest part of Iran, almost 70 km northeast of Andimeshk city (Khuzestan province), and 65 km southwest of Dorud city (Lorestan province). In recent paper, it has been compared the obtained Erm from plate loading tests with different stress values and different plate sizes Plate loading tests at Bakhtiari Dam site are carried out using rigid loading plates with diameters of 650 and 915 mm and under maximum stresses equal to 20 and 40 MPa. In this test, two opposite areas in test galleries are loaded using rigid loading plates by means of hydraulic pump system. During tests, the rock displacements are measured using borehole extensometers that fixed in several positions inside the boreholes drilled in the center of each loading area. The deeper extensometer in each borehole (used as a fixed point) is positioned at the end of borehole at depths more than 6 m. Erm is calculated according to ASTM D 4394 – 08. In case of two maximum stress values of 20 and 40 MPa, no significant difference is evaluated. Conversely, using two different diameter plates in same position result in significant differences between results. For high quality rock masses, the larger the plate diameter is, the greater the evaluated Erm is. This difference is recognized related to the ratio of gallery dimension proportional to loading plate size.