A plastic analysis of radial displacements at tunnel crown based on the non-associated flow rule

نوع مقاله : مقاله پژوهشی

نویسندگان

1 Mining Engineering Department, Faculty of Engineering, Vali-e-Asr University of Rafsanjan

2 M.Sc. in Rock Mechanics, & Independent Consultant in Mining and Geotechnical Projects

چکیده

This paper considers the non-associated flow rule to propose an analytical solution to calculate the ground reaction curve at the crown of a circular tunnel. This solution is based on the Mohr-Coulomb failure criterion and the dilation angle has been considered as a function of two factors of rock mass quality and confining stress. The results show that if the radial displacements are not controlled, a loosening zone is produced in the tunnel crown (cohesion=0.2 MPa and friction angle=25°). Moreover, based on the trend of the ground reaction curve at the tunnel crown, three new concepts “minimum required support pressure”, “maximum allowable strain”, and “safety factor based on the maximum allowable strain” was presented. Considering the interaction between the support characteristics curve and ground reaction curves, the efficiency of the associated flow rule to the non-associated flow rule was investigated. Results state that the use of the associated flow rule causes some sort of computational errors in determining the maximum allowable strain (too high) and consequently, the design accuracy of the support system is very low. Moreover, taking into account the associated flow and non-associated flow rules at the sidewall and tunnel crown, the interaction between the support characteristics curve and ground reaction curve was investigated. Based on the results, it was suggested that to design an optimal support system, it is necessary to calculate the safety factor based on the maximum allowable strain by considering the interaction between the support characteristics curve and the ground reaction curve at the tunnel crown. Finally, a procedure was presented for the design of the support system.

کلیدواژه‌ها

موضوعات


عنوان مقاله [English]

A plastic analysis of radial displacements at tunnel crown based on the non-associated flow rule

نویسندگان [English]

  • Hamid Mohammadi 1
  • Anna Soltani Esmaeili 2
1 Mining Engineering Department, Faculty of Engineering, Vali-e-Asr University of Rafsanjan
2 M.Sc. in Rock Mechanics, & Independent Consultant in Mining and Geotechnical Projects
چکیده [English]

This paper considers the non-associated flow rule to propose an analytical solution to calculate the ground reaction curve at the crown of a circular tunnel. This solution is based on the Mohr-Coulomb failure criterion and the dilation angle has been considered as a function of two factors of rock mass quality and confining stress. The results show that if the radial displacements are not controlled, a loosening zone is produced in the tunnel crown (cohesion=0.2 MPa and friction angle=25°). Moreover, based on the trend of the ground reaction curve at the tunnel crown, three new concepts “minimum required support pressure”, “maximum allowable strain”, and “safety factor based on the maximum allowable strain” was presented. Considering the interaction between the support characteristics curve and ground reaction curves, the efficiency of the associated flow rule to the non-associated flow rule was investigated. Results state that the use of the associated flow rule causes some sort of computational errors in determining the maximum allowable strain (too high) and consequently, the design accuracy of the support system is very low. Moreover, taking into account the associated flow and non-associated flow rules at the sidewall and tunnel crown, the interaction between the support characteristics curve and ground reaction curve was investigated. Based on the results, it was suggested that to design an optimal support system, it is necessary to calculate the safety factor based on the maximum allowable strain by considering the interaction between the support characteristics curve and the ground reaction curve at the tunnel crown. Finally, a procedure was presented for the design of the support system.

کلیدواژه‌ها [English]

  • Ground reaction curve
  • Non-associated flow rule
  • Dilation angle
  • Radial displacement
[1]                 Nikadat, N., Fatehi, M. and Abdollahipour, A. (2015). Numerical modelling of stress analysis around rectangular tunnels with large discontinuities (fault) by a hybridized indirect BEM. Journal of Central South University, 22: 4291–4299.
[2]                 Nikadat, N. and Fatehi Marji, M. (2016). Analysis of stress distribution around tunnels by hybridized FSM and DDM considering the influences of joints parameters. Geomechanics and Engineering, 11, 2: 269-288
[3]                 Lazemi, H.A., Marji, M.F., Bafghi, A.R.Y. and Goshtasbi, K. (2013). Rock failure analysis of the broken zone around a circular opening. Archives of Mining Sciences, 58,1: 165-188
[4]                 Vermeer, P.A. and Borst, R. (2010). Non-associated plasticity for soils, concrete and rock. Heron, 29(3):1–64.      
[5]                 Zhao, X.G. and Cai, M. (2010). A mobilized dilation angle model for rocks. Int. J. Rock Mech. Min. Sci., 47:368–384.
[6]                 Bagheri, B., Soltani, F. and Mohammadi, H. (2014). Prediction of plastic zone size around circular tunnels in non-hydrostatic stress field, International Journal of Mining Science and Technology, 4, 1: 81-85.
[7]                 Han, U.C., Choe, C.S., Hong,K.U. and Pak C. (2022). Prediction of final displacement of tunnels in time-dependent rock mass based on the nonequidistant grey verhulst model, https://doi.org/10.1155/2022/3241171
[8]                 Yi, K., Kang, H., Ju, W., Liu, Y. and Lu, Z. (2020). Synergistic effect of strain softening and dilatancy in deep tunnel analysis. Tunnell. Undergr. Space Technol., https://doi.org/10.1016/j.tust.2020.103280.
[9]                 Sharan, S.K. (2005). Exact and approximate solutions for displacements around circular openings in elastic–brittle–plastic Hoek–Brown rock. Int. J. Rock Mech. Min. Sci., 42:542–549.
[10]             Alejano, L.R. and Alonso, E. (2005). Considerations of the dilatancy angle in rocks and rock masses. Int. J. Rock Mech. Min. Sci., 42:481–507.
[11]             Zhao, X.G. and Cai, M. (2010). Influence of plastic shear strain and confinement-dependent rock dilation on rock failure and displacement near an excavation boundary. Int. J. Rock Mech. Min. Sci., 47:723–738.
[12]             Serrano, A., Olalla, C. and Reig, I. (2011). Convergence of circular tunnels in elastoplastic rock masses with non-linear failure criteria and non-associated flow laws. Int. J. Rock Mech. Min. Sci., 48:878–887.
[13]             Spitzig, W.A. and Richmond, O. (1984). The effect of pressure on the flow-stress of metals. Acta metal., 32:457-463.
[14]             Yoon, J.W., Stoughton, T.B. and Dick, R.E. (2007). Earing prediction in cup drawing based on non-associated flow rule. in:  CeasarDeSa, J.M.A., Santos, A.D. (Eds.), Materials Processing and Design: Modeling, Simulation and Applications, Pts I and II. Amer. Inst. Physics, Melville, 685-690.
[15]             Cvitanic, V., Vlak, F. and Lozina, Z. (2008). A finite element formulation based on non-associated plasticity for sheet metal forming. Int. J. Plasticity, 24:646-687.
[16]             Park, T. and Chung, K. (2012). Non-associated flow rule with symmetric stiffness modulus for isotropic-kinematic hardening and its application for earing in circular cup drawing. Int. J. Solids Struct., 3582-3593.
[17]             Stoughton, T.B. (2002). A non-associated flow rule for sheet metal forming. Int. J. Plasticity, 8:687-714.
[18]             Stoughton, T.B. and Yoon, J.W. (2006). Review of Drucker’s postulate and the issue of plastic stability in metal forming. Int. J. Plasticity, 22:391-433.
[19]             Safaei, M. (2013). Constitutive Modelling of Anisotropic Sheet Metals Based on a Non-Associated Flow Rule. PhD thesis, Ghent University.
[20]             Brown, E.T., Bray, J.W., Landanyi, B. and Hoek, E. (1983). Ground response curves for rock tunnels. J. Geothech. Eng., 109:15–39.
[21]             Carranza-Torres, C. and Fairhurst, C. (2000). Application of the convergence-confinement method of tunnel design to rock masses that satisfy the Hoek–Brown failure criterion. Tunnell. Undergr. Space Technol., 5(2):187–213.
[22]             Ghorbani, A. and Hasanzadehshooiili, H. (2019). A comprehensive solution for the calculation of ground reaction curve in the crown and sidewalls of circular tunnels in the elastic-plastic-EDZ rock mass considering strain softening. Tunnell. Undergr. Space Technol., 84:413–431.
[23]             Zhang, Q., Li, Y.J., Wang H.Y., Yin, Q. and Wang, X.F. (2022). Re-profiling response of heavily squeezed tunnels via ground reaction curves. Tunnell. Undergr. Space Technol., https://doi.org/10.1016/j.tust.2022.104411.
[24]             Park, K.H., Tontavanich, B. and Lee. J.G. (2008). A simple procedure for ground response curve of circular tunnel in elastic–strain softening rock masses. Tunnell. Undergr. Space Technol., 23(2):151–159.
[25]             Pacher, F. (1964). Deformationsmessungen in Versuchsstollenals Mittel zur Erforschung des Gebirgsverhaltens und zur Bemessung des Ausbaues. Felsmechanik und Ingenieursgeologie Supplementum, IV:149–161.
[26]             Detournay, E. The effect of gravity on the stability of a deep tunnel. Int. J. Rock Mech. Min. Sci., 21(6):349–351.
[27]             Hoek, E. and Brown, E.T. (1980). Underground excavations in rock. The Institution of Mining and Metallurgy, London, 1980.
[28]             Goodman, R. (1989). Introduction to rock mechanics. John Wiley & Sons.
[29]             Roussev, P. (1998). Calculation of the displacements and Pacher’s rock pressure curve by the associative law for the fluidity-plastic flow. Tunnell. Undergr. Space Technol. 13(4): 441–451.
[30]             Timoshenko, S.P. and Goodier, J.N. (1969). Theory of elasticity. McGraw-Hill Book Co Inc, New York.
[31]             Brady, B.H.G. and Brown, E.T. (1993). Rock mechanics for underground mining. London: Chapman & Hall.
[32]             Detournay, E. (1986). Elastoplastic model of a deep tunnel for a rock with variable dilatancy. Rock Mech. Rock Eng., 9(2):99–108.
[33]             Scholz, C.H. (1968). Microfracturing and the inelastic deformation of rock in compression. J. Geophys. Res., 73(4):1417–32.
[34]             Schock, R.N., Heard, H.C. and Stephens, D.R. (1973). Stress–strain behaviour of a granodiorite and two graywackes on compression to 20 kilobars. J. Geophys. Res., 78(26):5922–41.
[35]             Be´uelle, P., Desrues, J. and Raynaud, S. (2000). Experimental characterisation of the localisation phenomenon inside a Vosges sandstone in a triaxial cell. Int. J. Rock Mech. Min. Sci., 37(8):1223–37.
[36]             Wang, Y. (1996). Ground response of circular tunnel in poorly consolidated rock. J. Geotech. Eng., 122;703–708.